Advances on Mechanics, Design Engineering and Manufacturing III. Proceedings of the International Joint Conference on Mechanics, Design Engineering & Advanced Manufacturing, JCM 2020, June 2–4, 2020

Description

Preface Organization Committee JCM 2020 Members Conference Chair Conference Program Chair Conference Advisory Chairmen Scientific Committee Organizing Committee Contents Manufacturing Engineering Designing Powder Metallurgy Process - The Influence of High Sintering Temperature on Dimensional and Geometrical Precision 1 Introduction 2 Experimental Procedure 3 Results and Discussion 3.1 Dimensional Precision 3.2 Geometrical Precision 4 Conclusions References Process Parameters Effect on Weld Beads Geometry Deposited by Wire and Arc Additive Manufacturing (WAAM) 1 Introduction 2 Experimental Setup 3 Results and Discussion 3.1 Temperature Evolution 4 Geometry Evolution 5 Conclusion References A Parametric Study of Additive Manufacturing Process: TA6V Laser Wire Metal Deposition 1 Introduction 2 Protocol of Experiments 2.1 Model and Variables 2.2 Methods 2.3 Taguchi’s Experimental Design 3 Results and Analysis 3.1 Correlation Coefficient 3.2 Variance Analysis 4 Conclusion References Develop Model for Controlled Depth Milling by Abrasive Water Jet of Ti6Al4V at Jet Inclination Angle 1 Introduction 2 Proposed Model with the Inclination Angle of the Jet 3 Experiment 4 Result 5 Conclusion References Simulation and Experimental Validation of Secondary Dendrite Arm Spacing for AlSi7Mg0.3 Chassis Parts in Low Pressure Die Casting 1 Introduction 2 Secondary Dendrite Arm Spacing Analysis 2.1 Low Pressure Die Casting Simulation 2.2 Spectrochemical Analysis with Optical Emission Spectroscopy 2.3 SDAS Mapping Through Micrographs 2.4 Correlation Between Measured and Simulated SDAS 3 Experiments and Simulation Analysis on Case Studies 4 Conclusions References Influence of the Hole Surface Integrity on the Fatigue Strength of an Aluminium Drilled Part 1 Introduction 2 Experimental Work 2.1 Fatigue Tests 2.2 Surface Integrity Characterization 3 Discussion and Conclusions References Cold Working Process on Hard Metal Stacked Assembly 1 Introduction 2 Stacked Cold Expansion Process 3 Experimental Campaign 4 Results 5 Conclusion and Perspectives References Numerical Simulation and Experimentation of Additive Manufacturing Processes with Polyurethane Foams 1 Introduction 2 Foam Polyurethane Characterization 3 Comparison Between Experiments and Numerical Simulation 4 Use of Simulation to Apply a Speed Correction on a Trajectory in Order to Minimize the Form Defect 5 Perspectives 6 Conclusion References Analysis of Warpage Induced by Thick Copper Metal on Semiconductor Device 1 Introduction 2 Sample and Test Description 3 Warpage Measurements 4 Finite Element Model 5 Conclusions References Finite Element Modeling and Validation of Metal Deposition in Wire Arc Additive Manufacturing 1 Introduction 2 Proposed FE Metal Deposition Technique 2.1 Metal Deposition Modelling 2.2 Heat Input Modelling 2.3 Model Update 3 Validation 3.1 Results 4 Conclusions References Study of the Use of Sawdust and Mycelium Composite as a Substitute of EPS 1 Introduction 2 Materials and Methods 3 Results and Discussion 4 Conclusions References Topology Optimization Design of Internal Reinforcements in a Sailing Dinghy 1 Introduction 2 Methods 3 Case Study 3.1 Discussion 4 Conclusions References State of the Art on Robust Design Methods for Additive Manufacturing 1 Introduction 2 State of the Art 2.1 Robust Design 2.2 Robust Design for Additive Manufacturing 3 Conclusions and Perspectives References Topological Optimization of a Mechanical System with Adaptive Convergence Criterion 1 Introduction 2 The TOMS Method 3 Adaptive Coefficient of Convergence Ε 4 Conclusion and Perspectives References Design for Additive Manufacturing of a Topology Optimized Brake Caliper Through CAD-Platform-Based Systematic Approach 1 Introduction 2 Method 3 Case Study 3.1 Product Planning 3.2 Design 4 Results and Discussion References Product and System Engineering Evaluation of the Effects Caused by Mandibular Advancement Devices Using a Numerical Simulation Model 1 Introduction and Literature Review 2 Materials and Methods 2.1 Anatomical Model 2.2 Materials 2.3 Boundary Conditions 2.4 Meshing 3 Results and Discussions 4 Conclusions References Simulation of Dynamic Stresses on High Performance Engine Valve Spring System Considering Coil Clashing Effect 1 Introduction 2 Testing Equipment 3 Multibody Dynamic Models 4 Finite Element Dynamic Model 5 Results 6 Conclusion References Thread Couplings Stress Analysis by Radial Basis Functions Mesh Morphing 1 Introduction 2 Discretized Models 3 Parameterization 4 Results and Discussion 5 Conclusions References Computer-Aided Tolerancing Analysis of a High-Performance Car Engine Assembly 1 Introduction 2 Method 3 Case Study: V12 Engine Assembly 4 Discussion and Conclusions References Review of Product Design and Manufacturing Methods for Prosumers 1 Introduction 2 Methodological Description 3 Results 4 Conclusions References State of the Art for Evaluation of Inventive Design Solution Concepts 1 Introduction 2 Aim and Scope 3 Inventive Design Solution Concepts 3.1 Inventive Design Definition 3.2 Our Position in Inventive Design Process 3.3 Inventive Design Solution Concept Evaluation 3.4 Research Gaps in Inventive Design Solution Concept Evaluation 4 Conclusion and Future Research References Systemic Approach for Local Energy Mix Assessment 1 Introduction 2 Methodology 2.1 Simulation 2.2 Control Strategies 3 Case Study 4 Conclusion References Towards a Better Understanding of Open Source Hardware Design Reuse in Company-Community Collaboration 1 Introduction 2 Design Reuse in Company and Community 2.1 Design Reuse in Companies 2.2 Design Reuse in Communities 3 Design Reuse in Company-Community Collaboration 4 Conclusions References Comfort Driven Redesign: The Case of Library Chairs 1 Introduction 2 Materials and Method 2.1 Design from Experiment 2.2 Redesign of Library Chair 2.3 Experiment Setup 2.4 Participants 2.5 Questionnaires 2.6 Experiment Protocol 3 Results 4 Conclusions References Constraint Analysis and Optimization of NES System Based on Variable Pitch Spring 1 Introduction 2 NES Design Process 3 Nonlinear Constraint Analysis 4 Optimization Result 5 Conclusions References Generative Design in the Transmission System of a Skateboard 1 Introduction 2 Materials and Methods 3 Results 4 Discussion 5 Conclusions References Methodology of Product Sustainable Redesign. Case Study: Furniture of a Clothing Retail Store 1 Introduction 2 Methodology 3 Case Study 4 Conclusions References Enhanced Material-Driven Design Methodology: Luffa Cylindrica’s Case 1 Introduction 2 Methodology 3 Phase I: Luffa Cylindrica Understanding 3.1 Volumetric Characterization 3.2 Mechanical Characterization 3.3 Other Properties 4 Phase II: Conceptualization 5 Phase III and IV: Development and Prototyping 6 Conclusions References A Well-to-Wheel Comparative Life Cycle Assessment Between Full Electric and Traditional Petrol Engines in the European Context 1 Introduction 2 Materials and Methods 3 Results and Discussion 4 Conclusions References Product Eco-Design in the Era of Circular Economy: Experiences in the Design of Espresso Coffee Machines 1 Introduction 2 Product Eco-Design for Coffee Machines 3 Case Studies 4 Conclusions References A Novel Procedure to Design a Positionable and Stable Drilling Template for Spine Surgery 1 Introduction 2 Methodology 3 Conclusion References CAD and Interaction Feature-Based Modelling of Laryngoscope Blades for Customized Applications 1 Introduction 2 Materials and Methods 2.1 Parametrization 2.2 Parametric Modelling 2.3 Mechanical Tests 2.4 Additive Manufacturing of a Laryngoscope Prototype 3 Results and Discussion References Magnitude Finger Forces Analysis During Simulating Pseudo-Haptic Spring 1 Introduction 2 Experimental Protocol and Participants 3 Results and Discussion 4 Conclusion References Parametric Hull Design with Rational Bézier Curves 1 Introduction 2 Design Approach 3 Case Study 4 Conclusion References A Framework for Curvature-Based CAD Mesh Partitioning 1 Introduction 2 Related Work 3 Curvature-Based Framework for ISO GPS Partitioning 3.1 Initial Region Partition 3.2 Region Refinement 4 Case Study 5 Conclusion References A Topology Optimization Method for Stochastic Lattice Structures 1 Introduction 2 Materials and Methods 2.1 The Algorithm 2.2 The Case Study 3 Results and Discussion 4 Conclusions References Generative Design for Additively Manufactured Textiles in Orthopaedic Applications 1 Introduction 2 AMT Flexible Structures 2.1 CAD Modelling of Flexible Structures by Commercial Software 2.2 CAD Modelling of Flexible Structures by a New Approach 3 FEM Analysis 4 Prototype Manufacturing by Additive Manufacturing 5 Conclusions References Modeling Symmetric Minimal Surfaces by Mesh Subdivision 1 Introduction 2 Methods 3 Results 4 Conclusions References Analysis of the Accuracy of Reconstruction of a Human Cornea by Two Geometric Modelling Techniques: A Comparative Study 1 Introduction 2 Materials and Methods 2.1 Geometrical Reconstruction of the Human Cornea 2.2 Practical Application 2.3 Statistical Analysis 3 Results 4 Conclusions References Customization of Kayak Paddle Grips by Using Reverse Engineering, Computer Aided Design and Additive Manufacturing Tools 1 Introduction 2 Materials and Methods 2.1 Phase 1: Reverse Engineering of the Handgrip 2.2 Phase 2: Design of the Grip 2.3 Phase 3: Additive Manufacturing of the Grip 3 Results and Discussion 4 Conclusions References A Fast and Reliable Optical 3D Scanning System for Human Arm 1 Introduction 2 Software Design 3 Discussion and Conclusions References Sensitivity Analysis for Simulated Annealing-Based Fitting of CAD Models to Point Clouds of Digitized Parts 1 Introduction 2 Simulated Annealing-Based Fitting of CAD Models 3 Sensitivity Analysis 4 Results and Discussion 5 Conclusion References Digital Operative Guides for Helping First Responders in Public Buildings During Emergency Interventions 1 Introduction 2 Method 2.1 Operational Guide 2.2 Reduced Operational Guide 2.3 Digital Operational Guide 3 Results and Conclusions 4 Limitation and Further Research References Design and Optimization of a Photovoltaic Canopy for an Electric Vehicle Charging Station in Urban Environments 1 Introduction 2 Materials and Methods 3 Conclusions References Taking into Account Users’ Perceptions in the Design Process: Principles to Create a Digital Design Tool 1 Introduction 2 Methods 3 Results 3.1 Contributions from Literature 3.2 Requirements List 3.3 Digital Tool User Interface 4 Conclusion and Perspectives References Human, Knowledge and Decision Proof of Concept Experience in the SPES Experiment: First Solutions for Potentiometers Replacement in System Maintenance 1 Introduction 2 Case Study: Replacement of Potentiometers 3 Conclusions References A New Smart Web Platform for Plastic Injection Molds in Industry 4.0 Environments 1 Introduction 2 Methodology 2.1 Architecture of the Injection Molding Smart Platform 3 Results 4 Conclusions References Causality Learning Approach for Supervision in the Context of Industry 4.0 1 Introduction 2 Methodology of the Proposal 3 Use Case and Results 4 Conclusion and Future Work References Digitization of Operational Processes: Use Case of Standardization in an Assembly Learning Factory 1 Introduction 2 State of the Art 3 Methodology 4 Results 5 Conclusion References Enhanced Manufacturing Execution System “MES” Through a Smart Vision System 1 Introduction 2 State of the Art 3 Smart Visual Inspection System 4 Use Case 5 Conclusion References Design Rules Application in Manufacturing Industries: A State of the Art Survey and Proposal of a Context-Aware Approach 1 Introduction 2 Design Rules 3 State of the Art of Design Rule Application Tools 4 Introducing a Context-Aware Cognitive Design Assistant 5 Conclusion and Future Work References Semantic Enrichment of 3D Models Based on Ontology Integration 1 Introduction 2 State of the Art: Management of 3D Data 2.1 Standards and Tools for Managing 3D Data 2.2 Evolution of the Low-Level File Format 3 Semantic Enrichment of 3D Model: Proposal Vaquero 4 Conclusion References Essential Issues to Consider for a Manufacturing Data Query System Based on Graph 1 Introduction 2 Graph Database Consideration 3 Methodology 4 Experimentation Conditions and Results 5 Discussion References Design for Manufacturing and Assembly: A Method for Rules Classification 1 Introduction 2 Materials and Methods 2.1 Knowledge Acquisition Phase 2.2 Knowledge Processing Phase 2.3 Knowledge Representation Phase 3 Case Study: DfMA Rules Classification 4 Conclusions and Future Outlook References Education in Circular Economy: Focusing on Life Cycle Thinking at the University of the Basque Country 1 Introduction 2 Origin of the Master Degree in Circular Economy 3 Facts of the Master Degree in Circular Economy 3.1 Life Cycle Thinking: Ecodesign and Life Cycle Assessment 4 Specific Learning Outcomes or Competencies 5 Conclusions References Generation of Entrepreneurship Environments for New Product Development 1 Introduction 2 Methodology 3 Results 4 Conclusions References Engaging in Product Development as Means to Understand the Basics of Design 1 Introduction 2 Course Organization for Master Level 2.1 Questioning 2.2 Divergent Thinking and Convergent Thinking 2.3 Pedagogical Aspects of Teaching Design by PBL 3 Case Study 4 Discussion 5 Conclusion References Investigating Students’ Perception on the Outcomes of Technical Drawing University Courses 1 Introduction 2 Background 3 The Survey 4 Results 5 Discussion 6 Conclusion and Future Developments References Parametric Cost Modelling for Investment Casting 1 Introduction and Literature Review 2 Cost Estimation Relationship Building Process 2.1 Data Collection 2.2 CER Development 2.3 Validation 3 Conclusions References Initial Proposal for a General Systems Engineering Methodology to Early Design Phase Cost/Value Estimation 1 Introduction 2 Cost Estimation—A Systems Engineering Approach 3 Cost Estimation in the Interactive Design Environment Workflow—Knowledge-Based Engineering 4 Cost Considerations in Design Decisions 5 Conclusion References Industry 4.0 and Decision Making 1 Introduction 2 Decision Making Model 3 Conclusion References Multicriteria Decision Making Methods in Engineering Design: An Application on Medical Devices 1 Introduction 2 Method 3 Results 4 Discussion and Conclusions References Industry 4.0 and BIM: Do They Share the Same Objectives? 1 Context of the Study 2 Research Methodology 3 Content of the Selected Papers 4 Analysis 5 Conclusions and Perspectives References Smart Tightening Development for Aeronautical Bolted Assemblies in an Industry 4.0 1 Introduction 2 Experimental Campaign 3 Taguchi Factorial Experiment Plan 4 Results 5 Conclusion References Optimization of Reconfigurable Manufacturing Systems Configuration: A Literature Review 1 Introduction 2 Overview of RMS Configuration Optimization Papers 2.1 Main Focus of Papers Optimizing the RMS Configuration 2.2 Modelling and Optimizing the RMS Configuration 3 Conclusion References Author Index