Modern Techniques of Coating and Drying in Surface Engineering

Description

Modern Techniques of Coating and Drying in Surface Engineering takes into account the processes of coating and drying, and the surface defects involved in coating. It also comprises preparation of feed for the process of coating and the concept of roll coating. It provides the reader with the fundamental notion of advanced techniques applied in the process of coating and drying in the field of surface engineering so as to analyze the surface defects involved in these processes, preparation of feed for coating process and advantages of using dry coating metallic powder mixtures in drying processes. This book also discusses about experiment research on hot-rolling processing of non-smooth pit surface bioinspired superhydrophobic surfaces, fabricated through simple and scalable roll-to-roll processing, quality of electroless ni-p (nickel-phosphorus) coatings applied in oil production equipment with salinity, laser alloying advantages by dry coating metallic powder mixtures with SiOx nanoparticles and low-temperature, dry transfer-printing of a patterned graphene monolayer. Cover Title Page Copyright DECLARATION ABOUT THE EDITOR TABLE OF CONTENTS List of Contributors List of Abbreviations Preface SECTION I: INTRODUCTION TO COATING AND DRYING PROCESSES Chapter 1 Numerical Simulation of the Thin Film Coating Flow in Two-Dimension Abstract Introduction Coating Fluid Simulation Theory The Result of Calculation and Simulation Conclusion Acknowledgements References Chapter 2 Corrosion Study of Powder-Coated Galvanised Steel Abstract Introduction Experimental Details Results and Discussion Conclusion Acknowledgment References Chapter 3 Toward a Nearly Defect-free Coating via High-energy Plasma Sparks Abstract Introduction Results and Discussion Conclusions Materials and Methods References SECTION II: COATING AND SURFACE DEFECTS Chapter 4 Carbon based DLC films: Influence of the Processing Parameters on the Structure and Properties Abstract Introduction Materials and Methods Results and Discussion Conclusions Acknowledgments References Chapter 5 Superiority of Graphene over Polymer Coatings for Prevention of Microbially Induced Corrosion Abstract Introduction Results and Discussions Conclusion Methods Acknowledgements References Chapter 6 Seed Defective Reduction in Automotive Electro-Deposition Coating Process of Truck Cabin Abstract Introduction Define Phase Measure Phase Analyze Phase Improvement Phase Control Phase Conclusion References SECTION III: FEED PREPARATION FOR COATING Chapter 7 Indentations on Air Plasma Sprayed Thermal Barrier Coatings Prepared by Different Starting Granules Abstract Introduction Materials and Experimental Procedures Results and Discussion Conclusion Acknowledgments References Chapter 8 In Situ Carbon Coated LiNi0.5Mn1.5O4 Cathode Material Prepared by Prepolymer of Melamine Formaldehyde Resin Assisted Method Abstract Introduction Experimental Sections Results and Discussion Conclusions Acknowledgments References Chapter 9 Washcoat Deposition of Ni- and Co-ZrO2 Low Surface Area Powders onto Ceramic Open-Cell Foams: Influence of Slurry Formulation and Rheology Abstract Introduction Results And Discussion Experimental Section Conclusions Acknowledgments Author Contributions References SECTION IV: ROLL COATING AND RELATED PROCESSES Chapter 10 Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface Abstract Introduction Modeling of Pipe Inner-Wall Machining Robot Analysis of Hot-Rolling Machining Robot Text Set And Test Method Test Results And Analysis Conclusions Acknowledgment References Chapter 11 Bioinspired Superhydrophobic Surfaces, Fabricated Through Simple and Scalable Roll-To-Roll Processing Abstract Introduction Results Discussion Methods Acknowledgements References Chapter 12 Roll-to-Roll Slot-die Coating of 400 mm Wide, Flexible, Transparent Ag Nanowire Films for Flexible Touch Screen Panels Abstract Introduction Results Conclusion Methods Acknowledgements References Chapter 13 Surface Tension-Driven Self-Alignment Abstract Introduction Fundamentals Of Surface-Tension-Driven Self-Alignment Liquid Confinement Influence of Shape and Size Dynamics Process Integration Patents Outlook Acknowledgements References Chapter 14 Protruding Organic Surfaces Triggered by in-plane Electric Fields Abstract Introduction Results Discussion Methods Acknowledgements References Chapter 15 Quality of Electroless Ni-P (Nickel-Phosphorus) Coatings Applied in Oil Production Equipment with Salinity Abstract Introduction Deposition Process of Nickel-Phosphorus Mechanism And Properties of Ni-P Deposition Ni-P Coating: Specifications And Properties Corrosion Testing of Electroless Ni-P Coating Concerns Or Precautions Regarding Nickel-Phosphorus Coating Applied on Carbon Steel and Used In Extreme Conditions Conclusions References SECTION V: DRYING PROCESSES Chapter 16 Laser Alloying Advantages by Dry Coating Metallic Powder Mixtures with SiOx Nanoparticles Abstract Introduction Materials and Methods Results and Discussion Conclusions Patents Author Contributions Acknowledgments Appendix A References Chapter 17 Low-Temperature, Dry Transfer-Printing of a Patterned Graphene Monolayer Abstract Introduction Transfer-Printing of a Patterned Graphene Layer Results and Discussion Conclusion Methods Acknowledgements References Index Back Cover