Innovations and Technologies in Construction: Selected Papers of BUILDINTECH BIT 2022

Description

This book gathers the latest advances, innovations, and applications in the field of building design and construction, as presented by researchers and engineers at the International Conference BUILDINTECH BIT 2022, Innovations and Technologies in Construction, held in Belgorod, Russia, on March 9-10, 2022. It covers highly diverse topics, including building materials, industrial and civil construction, structural mechanics and theory of structures, computational methods and IT in construction, organization and technologies of construction production. The contributions, which were selected by means of a rigorous international peer-review process, highlight numerous exciting ideas that will spur novel research directions and foster multidisciplinary collaborations.  Preface Contents High-Efficiency Wall Materials Based on Technogenic Aluminosilicate Raw Materials 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Modernization of the Mill’s Working Bodies for the Production of Fine Building Materials 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Using of Citrogypsum in Alkali Activated Systems 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusion References Efficiency of Stabilization of Sandy, Coarse-Grained and Technogenic Soils with Polymer Complexes and Surfactants of Structural Layers of Highways 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusions References Investigation of Gas Release Processes in a Polymer Composite Filled with Amorphous Boron Under Thermal and Radiation Exposure 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Obtaining Energy Efficient Polymer-Bitumen Binders Using Polymer-Bitumen Concentrate 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusion References Effect of Cyclic Loading Level on Elastic-Strength Characteristics and Kinetics of Damage Accumulation in Polymers 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Research Methods for Flame Retardant and Construction and Technological Properties of Protective Coatings 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusions References Methodology for the Selection of Optimal Parameters of the Finite Element Mesh in Composite Materials Calculation 1 Introduction 2 Materials and Methods 3 Results 4 Discussion 5 Conclusions References Review Study of Recycled Aggregate Concrete Column Under Eccentric Loading 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusions References Surface Modification of ZrH2 with an Organosilicon Oligomer 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Formation of Copper Coating on the Surface of Titanium Hydride Using Quadruple Magnetron Sputtering 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Investigating of the Residual Stresses During the Extraction of a Polymer Product from an Extruder 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Compatibility of Polymer and Plasticizer—As a Key Factor in the Formation of Degradation-Resistant Bituminous Binder 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusion References Improving the Method of Assessing the Bearing Capacity of Complex Technical Systems 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Optimization of Foam Fiber Concrete Mix Design by Mathematical Modeling 1 Introduction 2 Materials and Methods 3 Results and Discussion 4 Conclusion References Analysis of Intermediates Produced During the Synthesis of Alkyd Resins 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Surface Structure of Modified Titanium Hydride Fraction 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Optimization of Parameters for the Production of Gypsum Binders Based on Gypsum-Containing Waste 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusion References Heat-Shielding Properties of Concrete Structures Reinforced with Composite Reinforcement 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Erosive Wear of Alumina Coated Polyimide Composite 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Biological and Climatic Resistance of Cement Composites Based on Biocidal Binders 1 Introduction 2 Materials and Methods 3 Results and Their Analysis 4 Conclusions References Calculation of the Parameters of the Grinding Load in a Ball-Tube Mill for the Production of Construction Materials 1 Introduction 2 Materials and Methods 3 Results and Discussion 3.1 Parameters of the Ball Movement Along the Inclined Partition 3.2 Separation of the Ball from the Inclined Partition 3.3 Speed and Inertia of the Ball at the Moment of Its Collision with the Mill Crushing Cylinder 4 Conclusion References Dynamic Behavior of an “Earth Dam-Foundation” Plane System Within Wave Theory 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Effect of Plasma Blast Furnace Slag Treatment on Properties of Blast Furnace Slag-Cement Mortar 1 Introduction 2 Methods and Materials 2.1 Materials Used 2.2 Methods 3 Results and Discussion 3.1 Analysis of Raman Spectroscopy 3.2 Investigation of the Blast-Furnace Slag Surface Before and After Treatment with Low-Temperature Non-Equilibrium Plasma 3.3 Effect of Plasma Modified BFS on Properties of BFS -Cement Mortar 4 Conclusion References Mechanical, Tribological, and Anticorrosion Properties of the Coating Produced by Magnetron Sputtering of a Ni–Cr–B4C Composite Target 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Correlation of Bitumen Emulsion Stability Factor with Aqueous Phase Parameters Evaluated at the Stage of Composition Design 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Electrochemical Co-deposition of Copper and Nanodispersed Tungsten Carbide on Titanium Hydride 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Light-Colored Ceramic Products from Red-Burning Clay Raw Materials 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusions References On the Effect of Operating Conditions on the Coupling of Non-metallic External Reinforcement with Reinforced Concrete Structure 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Research Study of Mixing Processes in the Pneumatic Mixer for Dry Construction Mixes 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusions References Improving the Calculation of Variable Cross Section Compressed Wooden Bars Stability 1 Introduction 2 Methods 3 Results and Discussion 4 Conclusion References Characterization of a Polymer Composite with a Hybrid Filler 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Finite Element Modeling of the Work of Bent Reinforced Concrete Elements of Rectangular Section in the Abaqus Software Environment 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Clay-Slag Autoclaved Composite Materials with the Usage of Activated Aluminosilicate Raw Materials 1 Introduction 2 Methods and Materials 3 Results and Discussions 4 Conclusion References Cellular Concrete Mixes with Bentonite Suspension 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusions References Foundation Type Influence on the Construction Site Seismicity 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Model of the Catastrophic Stage of Wood Damage Accumulation Under Uniaxial Compression 1 Introduction 2 Methods and Materials 3 Results and Discussion 3.1 Damage Functions 3.2 Simulation of Blow-Up Regime 4 Conclusion References Improving the Operational Reliability of Complex Technical Systems Operating in Corrosive Conditions 1 Introduction 2 Methods and Materials 2.1 Analysis of Corrosion Processes in CTS Structural Elements 2.2 Application of Strengthening Technology in CTS Elements Welded Joints 3 Results and Discussion 4 Conclusions References Power Calculation of Ball-Tube Mill Drives in the Construction Materials Industry 1 Introduction 2 Materials and Methods 2.1 The Power of the BTM Drive with Cross-Longitudinal Movement (CLM) of Grinding Bodies 3 Results and Discussion 4 Conclusion References Calculation of Reliability of Beam with Corrugated Wall with Limited Information About the Controlled Parameters at the Stage of Operation 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References White Cement Clinker Roasting Intensification 1 Introduction 2 Materials and Methods 3 Results and Discussion 4 Conclusion References The Influence of Electric Current on the Water Separation of Cements 1 Introduction 2 Materials and Methods 3 Results and Discussion 4 Conclusion References Analysis of the Effect of Cyclic Loading Mode on the Change in the Properties of Polymer Materials 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Modification of Properties and Study of Electrical Conductivity of Citrogypsum 1 Introduction 2 Materials and Methods 3 Results and Discussions 4 Conclusions References Improving the Quality of Building Materials Due to the Effect of Shear Deformation on the Parameters of the Grinding Process 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusions References Water-Resistant Clay and Slag Composite Materials of Autoclaved Hardening 1 Introduction 2 Methods and Materials 3 Results and Discussions 4 Conclusions References The Study of the Patterns of Soil Contact with a Solid Surface 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusion References Stress–Strain State Simulation for the Eccentrically Compressed Reinforced Concrete Columns with Local Prestress at the Manufacturing Stage 1 Introduction 2 Methods 3 Results and Discussion 4 Conclusion References Filled Polyurethane Foam with Improved Quality Indicators 1 Introduction 2 Methods and Materials 3 Results and Discussion 4 Conclusions References Author Index